河型发育过程的二维数值模拟研究

改进已有二维平面水沙模型,进一步考虑河床粗化、弯道二次流及河床结构对泥沙输运的影响;并针对河湾形态对崩岸的影响提出新的非粘性土崩岸模拟方法,使其能模拟边滩的形成。利用改进后模型分别对Yen弯道水槽泥沙冲淤试验及Friendkin室内弯曲小河塑造试验进行模拟;模拟结果与试验观测资料吻合较好,表明考虑弯道对泥沙输运及河岸崩塌影响的模型能够更准确反映天然河流演化过程,为研究河型演化机理及各控制因素变化规律提供新手段。     

冲蚀磨损与冲蚀、空蚀交互磨损的对比研究

基于计算流体力学(computational fluid dynamics,CFD)方法,数值对比研究了在模拟水轮机工况中不同转速时,冲蚀与冲蚀、空蚀交互作用时,转盘表面的流场(压力场、流体浓度分布),然后在转盘式磨损装置上,进行了汽液固三相冲蚀与空蚀交互磨损试验.结果表明:对于冲蚀磨损来说,随着转速增加,压力增大,在冲蚀作用下加入空蚀磨损,压力增高,磨损加剧;而对于交互磨损来说,随着转速增加,转盘表面的空蚀磨损区域从空化孔附近开始沿着转盘旋转的反方向偏移,并且磨损程度加剧;数值计算的气泡较多且压力梯度较高区域和试验转盘磨损区域基本一致,数值计算结果和试验结果吻合得较好.     

人牙釉质的酸蚀行为研究

通过体外原位酸蚀试验,采用显微硬度仪、台阶仪、SEM和EDX等考察了在pH=3.20的柠檬酸溶液作用下,人牙釉质表面硬度、组织结构、化学组成等性能随酸蚀时间的变化关系,初步分析了牙釉质在柠檬酸溶液中的酸蚀过程和机制.结果表明,在柠檬酸溶液中腐蚀1 min后,牙釉质无明显酸蚀损伤;腐蚀3 min后,牙釉质表面硬度及Ca、P含量均明显降低,釉质表面旱现酸蚀损伤,腐蚀深度为0.236 μm;随酸蚀时间继续延长,牙釉质表面损伤进一步加剧.形貌分析显示:在腐蚀初期,人牙釉质内的釉柱先于相邻釉间质发生酸蚀剥落,而釉柱丧失会进一步加剧釉间质的酸蚀,两者互相促进,最终导致牙釉质表面发生实质性的硬组织丧失.     

锡镍合金电磁屏蔽织物研制与镀层性能研究

在化学镀铜的涤纶织物上于焦磷酸盐体系电沉积均匀致密的锡镍合金层.改变镀液的NiSO4.6H2O、SnCl2.2H2O浓度比可获得不同锡含量、不同色泽的锡镍合金镀层.盐雾实验表明,含锡量为68.96%的电磁屏蔽织物表现出较好的耐蚀性和抗变色性.且其导电性优异,柔软、透气性好,具有柔和的外观,对人体无致敏性,在电磁兼容领域和民用市场有广阔的应用前景.     

空蚀坑周围彩虹区的形成机理

经过1 min的超声振动空蚀试验后,在不锈钢试样表面形成的空蚀坑周围出现环形彩虹区.表面检测结果表明,该区域经历了高于300℃的高温加热过程.数值计算结果表明在空泡溃灭形成的微射流的高速冲击下,试样表面材料在短时间内发生的塑性变形所释放出的能量是造成材料局部升温的主要原因.在塑性变形相同的情况下,材料的导热系数是影响彩虹环区域大小的关键因素.     

环境保护中辐射技术的应用研究

介绍了近年来利用稳定同位素C和N以及放射性元素^7Be和^137Cs作为示踪元素应用在土壤侵蚀、水土流失研究中所取得的重要进展,讨论了电子束辐照和γ射线辐照在工业废水和废气处理的机理及其应用,说明了辐射技术在环境保护中具有重要的作用。The important progresses of studies on water loss and soil erosion using stable carbon, nitrogen isotopes and ^7Be, ^137Cs as tracers is introduced. The mechanisms and applications of the electron beam and y rays irradiation in industrial effluent disposal and tail gas treatment are discussed, which indicates the importances of the irradiation technology in environment protection.     

镍铝介金属镀膜之抗坑蚀行为

采用3种原子百分比Ni52Al48,Ni60Al40及Ni70Al30成分的靶材以阴极电弧放电离子被覆技术制备不同组成的Ni＿Al薄膜于AISI1045中碳钢基材表面上,并观察镀膜微结构与成分随靶材成分的变化,评估应用Ni＿Al于抗坑蚀功能方面的可行性.研究结果显示:使用上述3种靶材所获致的镀膜组成依次为Ni62Al38,Ni63Al37及Ni69Al31,镀膜镍含量随靶材镍含量增加而增加.3种镀膜的相组成均以Ni3Al为主,从富镍Ni70Al30靶材所得的镀膜尚含有部分镍相.镀膜具有极强的附着性并反映在镀膜的抗坑蚀性上.在纯水中,所有的Ni＿Al镀膜试片均能提高中碳钢基材的抗坑蚀性,约达10倍.在3.5wt%盐水与3.5wt%盐酸中亦分别有两倍以上的效果.而在这3种测试环境中,3种镀膜试片的坑蚀损失差别均不明显,无法判断镀膜组成对抗坑蚀性的影响.从动电位极化曲线可以看出,镀膜试片均能大幅提高基材在盐酸与盐水溶液中的抗蚀性,然而因坑蚀破坏而形成的孔洞会由于孔蚀而导致腐蚀加剧,造成镀膜试片在腐蚀溶液中之抗坑蚀效果低于电化学量测时所预期的保护效果.     

风沙环境下钢结构涂层低角度冲蚀特性研究

针对风沙环境中钢结构涂层长期受冲蚀,涂层破坏直接降低钢结构体系耐久性的现状,采用能模拟风沙环境的气流挟沙喷射法对钢结构涂层试件进行了低角度冲蚀试验,用失重测量法测定涂层冲蚀失重量与沙剂量和冲击速度关系,进而评定冲蚀程度,用扫描电镜(SEM)观测分析涂层冲蚀区的微观形貌来分析冲蚀机理,并提出了涂层冲蚀程度评价计算公式.结果表明:涂层冲蚀失重量随沙剂量和冲击速度的增大而增加;低角度冲蚀主要为微切削作用,材料硬度起决定因素,高角度冲蚀主要为冲蚀挤压变形作用,材料韧性起决定作用,由于涂层材料硬度低而韧性高,故在低冲角下其受冲蚀程度严重;验证了评价计算公式用于评价涂层冲蚀程度的可靠性.研究结果将为准确评价风沙区钢结构体系耐久性提供依据.     

Cavitation erosion by shockwave self-focusing of a single bubble

The ability of cavitation bubbles to effectively focus energy is made responsible for cavitation erosion, traumatic brain injury, and even for catalyse chemical reactions. Yet, the mechanism through which material is eroded remains vague, and the extremely fast and localized dynamics that lead to material damage has not been resolved. Here, we reveal the decisive mechanism that leads to energy focusing during the non-spherical collapse of cavitation bubbles and eventually results to the erosion of hardened metals. We show that a single cavitation bubble at ambient pressure close to a metal surface causes erosion only if a non-axisymmetric energy self-focusing is at play. The bubble during its collapse emits shockwaves that under certain conditions converge to a single point where the remaining gas phase is driven to a shockwave-intensified collapse. We resolve the conditions under which this self-focusing enhances the collapse and damages the solid. High-speed imaging of bubble and shock wave dynamics at sub-picosecond exposure times is correlated to the shockwaves recorded with large bandwidth hydrophones. The material damage from several metallic materials is detected in situ and quantified ex-situ via scanning electron microscopy and confocal profilometry. With this knowledge, approaches to mitigate cavitation erosion or to even enhance the energy focusing are within reach.     

Effects of the Chodura sheath on tungsten ionization and emission in tokamak divertors

The decay of the electric potential in the sheath region in tokamak divertors occurs on a scale length on the order of the main ion gyroradius (Chodura sheath) due to magnetic fields lines intersecting the divertor plates at grazing incidence. As a consequence, high-Z impurities like tungsten ionize within the sheath region in attached plasma conditions. The modification of the electron distribution in the sheath region must thus be taken into account to accurately model ionization and emission of impurities within the sheath region. To that end, an analytical expression of the distribution of the vertical ionization path for impurities sputtered from divertor plasma-facing components is derived. This expression is then used to estimate the fraction of neutral impurities ionizing within the sheath and the average vertical ionization path, and to derive an effective SXB (the number of ionizations per emitted photon) coefficient which includes the effects of the variation of the electron distribution in the sheath region. These results are applied to tungsten impurities sputtered from divertor plates. It is shown that the SXB coefficient for neutral tungsten is significantly reduced in high-density attached divertor plasma conditions (n_e ≳ 5 × 10¹³ cm⁻³) because of the ionization of neutral tungsten well within the sheath region.